ISO 22514 PDF

The international standard ISO has been withdrawn and replaced by the standard ISO. In order to avoid confusion regarding. TECHNICAL ISO/TR REPORT First edition Statistical methods in process management — Capability and performance. Buy UNI ISO STATISTICAL METHODS IN PROCESS MANAGEMENT – CAPABILITY AND PERFORMANCE – PART 2: PROCESS CAPABILITY.

Author: Mikamuro Mizshura
Country: Cayman Islands
Language: English (Spanish)
Genre: Art
Published (Last): 8 February 2011
Pages: 230
PDF File Size: 1.87 Mb
ePub File Size: 5.59 Mb
ISBN: 190-4-48055-492-9
Downloads: 17705
Price: Free* [*Free Regsitration Required]
Uploader: Vojora

If the process ismonitored using a control chart, the control chart will show an in control state.

The following are the conditions that will apply for capability: The process results of these quality characteristics are categorized into eight possible distribution types. To comply with such a strategy,any organization will need to evaluate the capability and performance of its key processes. Capability is 22514 regarded as being related to the proportion of output that will occur within the productspecification tolerances.

It has been prepared to provide guidance about circumstances where a capability study is demanded or necessary to determine if the NOTE 2 A characteristic assigned to a product, process or system e. With non-normally distributed process isoo, the median is often a preferred alternative measure. Additionally, the estimation method using probability paper, although very simple to jso, isnevertheless somewhat crude and computational procedures are preferred see Annex C. Alternatively, the calculations can bemade directly in the original scale of the measurements.

NOTE These formulae assume the estimated indices have been computed using a standard deviation based on thetotal sample size N. The proportion nonconformingdepends upon the distribution and the value of the index. NOTE 7 Capability conditions are very restrictive and include: Is formulae in the above table can be isk to any distribution.


NOTE 3 Care should isl exercised in using this measure as it may contain a component of variability due to specialcauses the value of which is not predictable. Using the above example of a CpkU of 0,86 and a CpkL of 0,91, the estimated proportion beyond thespecification limits U and L may be read directly from Table 3 as 0, 9 and 0, 2. The data from each cavitymight form a single normal distribution. NOTE 3 For a non-normal distribution 2. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.

Process capability ieo and performance measures [Technical Report]In the future, it is planned to revise 22154 The smaller this index becomes,the better the process is deemed to have performed. This part of ISO describes methods by which thesecan be computed.

They contain a digital watermark to protect the copyright. Thus, if meaningfulinformation about the distribution of a characteristic 2. NOTE 3 For a normal distribution 2. If there is a change to those conditions, it will necessitate a new process study;b assess the short-term and long-term measurement variabilities as percentages of the total variability and minimize them;c preserve the process stability and maintain its statistical control;d estimate the remaining inherent variation; ande select an appropriate measure of capability.

In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. This is often estimated from the mean range value, Rtaken from a range R chart when the process is stable and in a state of statistical control as indicated in 5.


The expression for process capability takesthe asymmetric form: Several indices are given. An example of this is shown in Figure 2.

ISO 22514-2:2013: Statistical methods in process management – Capability and performance – Part 2:

The statistical methods described in ISO The main task of technical committees is to prepare International Standards. If attributes data are generated by a measurement system that evaluates a variables measurement as a passor fail judgement, care must be taken to minimize any measurement system variation. The distribution has threeparameters: Statistical methods in process management – Capability and performance – Part 7: NOTE 2 The outcome is a distribution 2.

Hence Sw should be used with extreme caution. ISO shall not be held responsible for identifying any or all such patent rights.

ISO Pages 1 – 50 – Text Version | FlipHTML5

The method is illustrated below with some often encountered distributions. NOTE 3 In certain circumstances, the standard deviation, Sw, that represents only within subgroup variation can be used as an estimator for St: Please proceed with checkout.

As long as the process remains in statisticalcontrol, it will continue to produce the same proportion out-of-specification. They are unsuitable for count or attribute data and information 222514 the expression of measures for such data will be found later in 4.