IEC 61310 PDF

Find the most up-to-date version of IEC at Engineering Buy IEC Ed. Safety of machinery – Indication, marking and actuation Part 1: Requirements for visual, auditory and tactile signals from SAI Global. Buy IEC Ed. Safety of machinery – Indication, marking and actuation Part 2: Requirements for marking from SAI Global.

Where an operator has control or can intervene, the signal shall continue at least until the operator intervenes.

Safety distances to prevent hazard zones being reached by upper and lower limbs BS EN Users are responsible for its correct application. For further discrimination and information, and especially to give additional emphasis, a flashing light should iiec used. Idc specifies a system of colours, safety signs, markings and other warnings, intended for use in the indication of hazardous situations and health hazards and for meeting certain emergencies. NOTE 1 Figures 2 and 3 show zones of recommended and acceptable, vertical and horizontal fields of vision.

Contact the Information Centre. Requirements for visual, acoustic and tactile signals IEC If the document is revised or amended, you will be notified by email. Need more than one copy? Whilst their applications are mainly for electrotechnical purposes, the symbols shall be used for other types of actuators, for example, mechanical, hydraulic, using the same function. It should not be summed up with the orange entries The translation is wrong or of bad quality. Telegraphy, facsimile and data communication IEC It is incorporated by Royal Charter.

GSO IEC – Standards Store – GCC Standardization Organization

NOTE To be used in association with the symbol Thank you very much for your vote! Compliance with a British Standard cannot confer immunity from legal obligations.

For dated references, only the edition cited applies. Requirements for visual, aud it ory a nd tactile si gnals IEC Under certain conditions such as reduced visibility it may be necessary to rely on tactile signals alone.

BS EN 61310-1:2008

Colours of indicators and actuators shall be in accordance with Table 2. It is the constant aim of BSI to improve the quality of our products and services. NOTE To be used particularly when symbol is also used on the same equipment. NOTE See also symbol Information regarding online access to British Standards via British Standards Online can be found at http: It presents the UK view on standards in Europe and at the international level.

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. The meaning of a supplementary code shall be evident to the operators and shall be in accordance with Table 3. MeansCharacteristicType of sound Tone Noise Spoken message Pure tone Selected frequency TimeChangeof- frequency composition over time – sound volume over time – total duration 5.

Design principles for safety signs in workplaces and public areas ISO You may delete a document from your Alert Profile at any time.

Figure 3 — Zones of horizontal field of vision — 12 —EN Please click on the reason for your vote: Figure 4 — Examples of shapes that can be discriminated by touch alone Table 6 gives examples of means of coding. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. This is not a good example for the translation above.

Not more than five different shapes, such as the examples given in Figure 4, shall iev used in one application. Click to 16310 more. A list of organizations represented on this committee can be obtained on request to its secretary.

BS EN 机械安全.指示丶标记和传动作用.视觉丶听觉和触觉信号的要求 – MBA智库文档

Other requirements and other EC Directives may be applicable to the products falling within the scope of this standard. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.

BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. IEC Stand-by To identify the switch or switch position by means of which part of the equipment is switched on in order to bring it into the stand-by condition.

Learn more about the cookies we use and how to change your settings. Where a product family or dedicated product standard 6310, its requirements take precedence.

It also specifies ways of coding visual, acoustic and tactile signals for indicators and actuators to facilitate the safe use and monitoring of the machinery. Please first verify your email before subscribing to alerts.