ELDO SPICE PDF
I need to run several netlists in ELDO since the first netlist has Typical corner .inc netlist_tt) i need to change it for the second run for .inc. The spice simulator we will use to simulate Design Architect (DA) designs is called ELDO. ELDO is invoked by typing eldo, where filename is the file. pole approximation (DPA) to enhance simulation speed. An alternative built-in SPICE solver. Device model libraries fully compatible with Eldo and HSPICE.
|Published (Last):||12 May 2011|
|PDF File Size:||15.81 Mb|
|ePub File Size:||1.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
Reply 14 – May 14 th, 6: Add electrical source definition lines as follows: Pavel, For the most part, they should work as is.
This will plot the voltage at nodes in and out from your design. Please follow the Forum guidelines. It didn’t like function trunc.
I’d skip this and just get the normal simulation to run, and study later how the ELDO soice differs from the Spectre way. Boosting performance over standard analog simulation can help in two ways. Spice Eldo Aternating netlist and include files Hi Dino Could you show the output log, to try to understand the error you get?
In Eldo model there are functions for example trunc that are not recognized by Spectre parser. AvendesoraInform and QuantiPhy.
CMOS Technology file 1. Sldo two acceleration factors naturally combine to offer a very significant speed-up over Eldo Classic. Error found by spectre during circuit read-in. The acceleration of multi-threaded simulations is a consequence of the natively parallel code of the new Eldo Premier simulation kernel and its dedicated data structures.
ModelSim – How to force a struct type written in SystemVerilog?
Synthesized tuning, Part 2: Hierarchical block is unconnected 3. Distorted Sine output from Transformer 8. There are quite a lot of differencies. When I try replace elddo by intparser gives an error. The command should be changed to the following: Some of our other sites that you might find useful: Losses in inductor of a boost converter 9.
I don’t know if the CMI interface for Spectre is spce documented, if that’s your question. The acceleration of single-thread simulation is provided by new algebraic techniques for the resolution of the system of non-linear differential equations that analog simulators must solve.
I think you also need a license key. Spectre has probably a totally different way to define a probability distribution for a simulation parameter, which in this case is not a model parameter, but simply a subcircuit parameter local to the subcircuit Geoffrey, I don’t use leading “.
In instruction twenty-three 23the Accusim viewpoint needs to be changed. How do you get an MCU design to market quickly? Have you tried that? What does “intermediate step” mean? Reply 10 – May 9 th, 4: I also changed parameter names to lowercase to be them compatible with Spectre bsim4 parameters. What is this file and can I use it? Dec 242: This command does NOT seem to be supported with Eldo version 5.
The Designer’s Guide Community Forum – using Eldo models in Spectre?
EZwave is extremely efficient for the manipulation of huge databases and can load gigabytes of data in seconds. Reply 7 – May 9 th, 1: Critically important simulations that historically took a very long time to run, many times days or even weeks, can now be performed significantly faster from 2.
Reply 4 – May 8 th, 5: If I properly undestand you, the contents of this wldo is compiled models. Generating Eldo netlist 0.
So where is the problem? Reply 2 – May 7 th, 7: To run ELDO, type esim.
Analog/Mixed-Signal Verification | InnoFour BV
At the begining of Eldo model there is following piece of code Code: Add an input waveform: Useful commands to define and view bus signals in ELDO: Reply 3 – May 7 th, 8: Optimized for Single and Multi-Threaded Application The acceleration of single-thread simulation is provided by new algebraic techniques for the resolution of the system of non-linear differential equations that analog simulators must solve.
Eldk I tried to generate netlist elddo small test schema please, see on the picture. In instruction twelve 12the model property should be changed to pch. The Page Composition menu option can be used to plot wpice of the signals on a single graph. Measuring air gap of a magnetic core for home-wound inductors and flyback transformer 7. But it was not sufficient.