DANFOSS EKC 102 A PDF
EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D. EKC B Controller with two relay outputs, extra temperature sensor and digital EN and EN , A2 Weight = g Danfoss can accept no.
|Published (Last):||10 October 2014|
|PDF File Size:||10.30 Mb|
|ePub File Size:||15.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
Roof mounted industrial Electrical defrosting air cooler low temperature DJ series for cold room.
If the settings in the controller are to be protected with an access code you can s a numerical value between 0 and The function is defined in o Defrost The controller contains a timer function that is zeroset after each defrost start.
Set password Factory setting If you need canfoss return to the factory-set values, it can be done in this way: When there is defrost with clock function on the DI input the interval time must be set for a somewhat longer period of time than the planned one, as the interval time will otherwise start a defrost which danffoss little later will be followed by the planned one.
If you push the top button in this situation you can see the alarm report in the display.
There is no temperature monitoring during case cleaning. The function can only be used in 1: ON-time in minutes Min. Low temperature alarm A4: Interval between defrost starts The function is zeroset and will start the timer function at each defrost start.
The setting will be the defrost time if d10 is selected to be 0 EKC c30 d01 d02 d03 d04 Time staggering for defrost cutins during start-up The function is only relevant if you have several refrigeration appliances or groups where you want the defrost to be staggered in relation to one another.
There are two kinds of error reports – it can either be an alarm occurring during the daily operation, or there may be a defect in the installation.
The display shows the actual room temperature, but by activating the keys the display changes To the set or the actual temperature of the defrost sensor.
Find the parameter code you want to change and push the middle buttons until value for the parameter is shown.
Controller for temperature control – EKC 102 Manual
There is no sensor -d-: The controller will register when the input is reopened. See the significance in the Fault Message section. Normal function where the relay cuts in when refrigeration is demanded 1: Thermostatic Expansion Valves flow direction: Via three pushes on a switch you change from one phase to the next phase.
Integrated refrigeration-technical functions Defrost on demand in 1: Sensors Sair is thermostat sensors. Between two defrosts the S5 temperature will become lower the more the evaporator ices up the compressor operates for a longer time and pulls the S5 temperature further down.
When the compressor is stopped, it must remain stopped for at least x minutes. Order number or SW version do not match 9: A-alarms will not become visible until the set time delay has expired. A-model for simple regulation B-model where an alarm function and possibly also a digital input will be required C-model where the defrost temperature also enjoys top priority D-model with fan function, change-over between temperature reference and case cleaning function All these four controllers are without data communication.
Contact details entered above are not used to send newsletters or other advertisements. China Good Quality Box type condenser Supplier.
Controller for temperature control – EKC Manual |
The function is not active during a defrost or start-up after a defrost. Normal display Normal display shows the temperature value from the thermostat sensor Sair. After paying for this item you will be awarded: Lower alarm limit Here you set when the alarm for low temperature is to start. Copying to copying key incorrect. Condenser temperature alarm E1: EKC D Controller with three relay outputs, two temperature sensors and digital input. Showing of a negative figure spells problems.
Here you set how large a slide of the S5 temperature can be allowed. Easy product returns Buy a product and check it in your own time, at home.
When the value is passed, a defrost will start. Running times To prevent irregular operation, values can be set for the time the compressor is to run once it has been started. Enter danfosss details and we will notify you, when the product is available. This happens when the temperature reaches the upper part of the differential.
OFF-time Time delay for cutin of comp. If this description is not sufficient, please send us a question to this product.