ASTM D4791 PDF
This standard is issued under the fixed designation D; the number 1 This test method is under the jurisdiction of ASTM Committee D04 on Road. RELEVANT DOCUMENTS. ASTM D Standard Test Method for Flat Particles, Elongated Particles, or Flat and. Elongated Particles in Coarse Aggregate. The standard flat and elongated particles in coarse aggregate test is: ASTM D Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse.
|Published (Last):||9 January 2007|
|PDF File Size:||10.85 Mb|
|ePub File Size:||20.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Asphalt QMS Manual – connect. Two procedures, Method A and Method B, are presented in this standard.
BoxLewis Center, Ohio Asstm test method covers the determination of the percentages of flat particles, elongated particles, or flat and elongated particles in coarse aggregates.
When used on aggregates of a known size, the void content provides the user with an indication of the angularity, sphericity and surface texture as compared to other course aggregates of the same grading.
The blending shall produce a consistent and acceptable product.
Method A is a reflection of the original procedure as developed prior to Superpave and is intended for all non-Superpave applications. The plant shall blend and mix the materials to meet the specifications and to secure the proper moisture content for compaction.
S4791 procedures, Method A and Method B, are presented in this standard.
specification of flat and elongated particles
A flat and elongated piece is defined as one having a ratio of length to thickne ss greater than five. Currently, the Superpave mix design system currently specifies a maximum limit of 10 percent of flat and elongated particles at the 5: Apparatus Proportional Caliper Device.
Method B is a comparison of the maximum particle dimension to the minimum particle dimension and is intended for use with Superpave specifications. For Classification of Flat Particle Testing:. E4791 overflow pan and material handling scoop separately. To print astn manual completely, please, download it.
Particle d elongated when its length longest dimension is more than 1. The SI units in parentheses are for information purposes only.
Determine the proportion of the sample in each group by mass.
Active Risk Management
Six labeled openings between pairs of metal pins measure particle from each of the six sieve cuts below 50mm. Construction and Materials Manual Wisconsin Department of The granular base is typically dense graded, with the amount of fines limited to promote drainage.
Comments to this Manuals Your Name. These instructions are a general guide for operation of this. Proportional Caliper for measuring flat and elongated particles Taking for example the current methodology for measuring flat and elongated particles, as per ASTM specification ….
Units are constructed of durable plated steel, asym tooled for accuracy. Flat and elongated particles of aggregates, for some construction uses, may interfere with consolidation and result in s4791, difficult to place materials. Slag shall be air-cooled, blast furnace slag, and ….
Testing equipment for the construction industry – CONTROLS
Length – the maximum dimension. Effects of flat and elongated particles upon properties of Flat or aastm aggregate particles can, if present in sufficient number, 1 impede compaction or 2 d47911 HMA behavior by fracturing during compaction. Enter text from picture: For Classification of Elongated Particle Testing:. Use the proportional caliper device, shown in Figure 1. This test method covers the determination of the percentages of flat particles, elongated particles, or flat and elongated particles in coarse aggregates.
Find out why Close. No thanks 1 month free. Scratch Hardness Tester— H Scratch Hardness Tester determines quantity of soft particles in coarse aggregates on basis of scratch hardness.
Slag shall be aircooled, d4719 furnace slag, and shall have a compacted weight of not less than Plunger is mounted on support stand, permitting plunger to lower and raise freely. This test method provides a means for checking compliance with specifications that limit such particles or to determine the relative shape characteristics of coarse aggregates.
Link to Active This link will d4971 route to the current Active version of the standard. The standard flat and elongated particles in coarse aggregate test is: Subatomic Particles Explained In Under 4 ….
Coarse aggregate shall be aggregate retained on the No. Do not add soil materials such as clay, loam, or silt to compensate for a lack of fines in the aggregate. The excess heaped astn is struck of using the included bar, the mass is measured, and the void content is computed.
Division of Engineering Services::